¡¡¡¡ Contemporary Products & Design Inc., C&D, manufactures a complete line of fire retardant cornice mouldings and panel mouldings in standard 8 feet length. Our moulding products are made from high density polyurethane and look rich and luxurious. We take great pride in the quality and workmanship of our products. Every piece of our products goes through strict quality control and meticulous finishing process to produce sharp line definition, polished refined look and smooth texture surface before it is delivered to our customers. We manufacture one of the highest quality architectural moulding products in the market and we are committed to develop new product line with new design every year.

         Our products are for both interior and exterior uses. They are ideal for beautification and embellishment of residential homes, hotels, spas, restaurants, shops, and offices.

         Installation of polyurethane mouldings is quick and effortless. They are handled in the same manner as in wood but are much easier and faster than wood or plaster to install. Our products meet ASTM international standard for building materials.

Product features:
¡¡  ¡ñ Fire flame retardant: C&D mouldings have been tested and certified to meet ASTM fire rating standard and British fire safety code standard. They are classified to be fire retardant building materials and are non-combustible and non-conductive to surface spread of flame. Test reports and certificates are available upon request.

       ¡ñ Ease of Installation: C&D mouldings are light weighted and easy to install. They can be nailed, drilled, glued and sawed like wood but only require half of the cost and time to installing wood or plaster mouldings. Our products can be used in both interior and exterior settings.

       ¡ñ Durability: C&D polyurethane mouldings are made from high density foam and are strong and durable. They will no rot, crack, deform, split, warp, bow or subject to insect damage. They are high temperature tolerant, impervious to water and moisture, and readily accept any latex or oil-base paint finish.

       ¡ñ Pre-primed: C&D polyurethane mouldings are pre-primed and can be paint or stained immediately.

       ¡ñ Color: Standard color is white.

       A complete line of fire retardant mouldings in an assortment of traditional and contemporary styles.

¡¡ ¡¡
¡¡

     PU flexible mouldings permit flexing so they can be fitted along curves and around corners to meet any installation need. (special order)

       

        Angle shape allows pieces to fit smoothly against walls and ceilings. Overall effect is a better installed finish with superb views of architecture beauty. (C&D registered trademark is on back of each piece of our products)

     

     PU cultured stone are light weighted and easy to install . They are ideal for both interior and exterior trims. They blend perfectly with either classical lines or contemporary designs and add warmth and beauty to any site.

¡¡

Installation Guide :

       When installing polyurethane mouldings, treat them just as if they were wood. They can be cut, drilled, nailed, and screwed like wood. We recommend the use of trim head drywall screws as fasteners. They are self counter sinking and leave a hole that is easy to fill.

  1. Place a piece of moulding on the wall and pencil the edges of where the moulding touches the ceiling and the wall. Also, take a pencil and mark all the of the stud locations on the wall.
  2. The cornice can be installed directly over the stucco surface. However, for best result, remove the stucco by scraping it off with a 2¡± wide putty knife.
  3. Begin your installation by fastening all of your corners first.
  4. To determine the length of moulding, measure the distance between each corner block. If, for example, the distance between two corners is at least 7 feet, be sure to add an additional 1/8¡± to that length so that the moulding can be ¡°sprung¡± into place. Before you spring the moulding into place, put a bead of urethane adhesive along the top and bottom edge of the moulding where it will meet the backing as well as the edges that touch the corner block.
  5. Once the moulding is in place, be sure to remove all excessive immediately. Remove of the adhesive can be done with a soft, lint-free cloth.
  6. All nail or screw holes can now be filled with quality sand able, paintable, non-shrinking latex filler (spackling).
  7. We recommend that you use a premium pintable ¡°siliconzed¡± (or ¡°super latex¡±) latex adhesive caulk with polyurethane products. This will act as a bedding surface which will fill any gaps caused by the unevenness of walls or ceilings. The same material can be used to blend joints and edges.
¡¡¡¡

 1

 2

   
   

 3

 4

   

5

 6

7

8

9

10

11

12

   

13

¡¡¡¡¡¡
 
90 Degree Corner Block Installation:

¡¡ ¡¡ ¡¡
1
2
3
¡¡ ¡¡ ¡¡
¡¡ ¡¡ ¡¡
4
5
6
¡¡ ¡¡ ¡¡
7
8
9

¡¡

Copyright © 2004 Contemporary Products & Design. Inc.
All rights reserved